Proximity/Occupancy Sensors Finished Units(6976)

Part	Manufacturer	Description		Stock	Action
815-UCC2805DG4	Texas Instruments	UCC2805DG4 Overview Capsuled in the SOIC package, the switching controller can be used for a wide range of applications. There is sufficient capacity to generate switching controller for outputs 1. Switching can be done at 1MHz with this switching controller. SWITCHING CONTROLLER analog IC connects the switch converters. A switching converters's terminal (s) sits at the DUAL position. An array of 8 terminations of dc switching. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 10V. Total pins of switching converter are 8. Switching converter is a type of Switching Regulator or Controllers in particular. The minimum input voltage of the dc dc voltage regulator should be 4V. Statistically, the DC regulator outputs 4V voltage. Voltage regulator dc to dc is designed to operate at 50 % duty cycle during power-ups and power-downs to ensure reliability. The Surface Mount makes DC switcher suitable for most applications and prototypes. The switching controller works at a frequency of 1MHz. Keep dc regulator at a temperature of -40°C or above. There should be 85°C temperature above 85°C degrees Celsius when dc regulator runs. 1 functions are available in total for the switch converters. It is planned to design voltage regulators switchings with 8 pins. At maximum frequency, the controller can switch at 1MHz. Inputs of 1A are ideal for this component. This algorithm outputs a value of 1V in normaloperation. A supply voltage of 10V is required. It is important that the controller is supplied with 30mA more than 30mA volts of current. According to its maximum supply voltage rating, the voltage controller is rated 12V. UCC2805DG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 50 % Frequency: 1MHz UCC2805DG4 Applications There are a lot of Texas Instruments UCC2805DG4 DC to DC converter applications. Smoke prevention equipment Hydraulic presses Experimental setup Radio equipment Magnetohydrodynamic power Household control circuits Nuclear power plants Industrial robots Laboratories Thermal power	PDF	999 In-stock	Get Quote
815-UC2525BDWTRG4	Texas Instruments	UC2525BDWTRG4 Overview In the SOIC package, the switching controller meets most application requirements. There is sufficient capacity to generate switching controller for outputs 2. There is a Tape & Reel (TR) solid enclosure around the pmic. It can switch at 400kHz. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. DUAL are the position of the terminal of the switching converters. Various 16 terminations. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 20V. There are 16 pins on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. DC regulator outputs 5.1V voltage based on test statistics. Voltage regulator dc to dc is designed to operate at 50 % duty cycle during power-ups and power-downs to ensure reliability. A frequency of 450kHz is set for the switching controller. You should keep dc regulator at -40°C degrees or higher. There should be 85°C temperature above 85°C degrees Celsius when dc regulator runs. 1 functions (s) are included in the switch converters. Designing voltage regulators switchings with 16 pins. Switching can take place at a maximum frequency of 400kHz. It is possible to set the input voltage as 35V for nominal working statuses. This is an ideal solution for switching controllers with 100mA inputs. During normaloperations, it outputs a value of 18V. Voltage rating is 35V. UC2525BDWTRG4 Features Switching Frequency: 400kHz PULSE WIDTH MODULATION Max Duty Cycle: 50 % Frequency: 450kHz UC2525BDWTRG4 Applications There are a lot of Texas Instruments UC2525BDWTRG4 DC to DC converter applications. Network technology Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots Industrial controllers Die casting equipment	PDF	1791 In-stock	Get Quote
815-UCC2808APW-2G4	Texas Instruments	UCC2808APW-2G4 Overview As a result of TSSOP compact design, the switching controller is compatible with most applications. There is sufficient capacity to generate switching controller for outputs 2. An enclosure of Rail/Tube is used to package the PMIC. Using this switching controller, it is possible to switch at 1MHz. A SWITCHING CONTROLLER analog IC is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. An array of 8 terminations of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's voltage input is 10V. Pins number 8 of switching converter in total. Switching converter is a type of Switching Regulator or Controllers in particular. Input voltage of dc dc voltage regulator should be 4.3V. At most, the dc to dc regulator accepts 13V input voltage. To ensure the reliability under power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set as 50 %. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. There is 1MHz frequency setting on the switching controller. Ideally, dc regulator should be kept at a temperature of -40°C or higher. There should be 85°C temperature above 85°C degrees Celsius when dc regulator runs. 1 functions are available in total for the switch converters. Designing voltage regulators switchings with 8 pins is one of the most important aspects of the process. The controller can switch at the maximum frequency of 1MHz. A 100mA input switching controller would benefit from it. It outputs a value of 500mV in normaloperating procedures. Switching controller is necessary to provide a voltage of 10V. Voltage maximum is rated 15V. UCC2808APW-2G4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 50 % Frequency: 1MHz UCC2808APW-2G4 Applications There are a lot of Texas Instruments UCC2808APW-2G4 DC to DC converter applications. CMM Window air conditioners seismic instrument power circuits Product testing Various precision measuring instruments Gear/thread machining machines Mobile phones Imported equipment Adjustable voltage or current linear circuits CNC system	PDF	999 In-stock	Get Quote
815-UC3827DW-2G4	Texas Instruments	UC3827DW-2G4 Overview The switching controller fits in the SOIC package and is ideal for most applications. For 3 outputs, the dc motor controller is appropriate. This switching controller can switch at 500kHz. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. Switching converters are designed with the terminal (s) at position DUAL . A variety of 24 terminations are available in dc switching. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. DC switcher's input voltageis set to 15V. Total pins of switching converter are 24. Specifically, switching converter falls under the Switching Regulator or Controllers category. A duty cycle set at 95 % ensures voltage regulator dc to dc reliability during power-on and power-off. There is 450kHz frequency setting on the switching controller. To better satisfy the need, DC to DC voltage regulator has a value of CAN ALSO WORK IN CURRENT MODE. At 0°C and above, dc regulator should be kept. A temperature of 70°C more than 70°C degrees Celsius should be maintained in the undc regulator. Switch converter has 1 total function(s). There is a design for voltage regulators switching with 24 pins. Maximum frequency of the controller is 500kHz. Input voltage can be set to 15V for nominal working status. Inputs of 100mA are ideal for this component. During normaloperations, it outputs a value of 2.5V. Switching controller is necessary to supply a voltage of 15V. Voltage rating is 20V. UC3827DW-2G4 Features Switching Frequency: 500kHz PULSE WIDTH MODULATION Max Duty Cycle: 95 % Frequency: 450kHz CAN ALSO WORK IN CURRENT MODE UC3827DW-2G4 Applications There are a lot of Texas Instruments UC3827DW-2G4 DC to DC converter applications. Computer monitoring equipment of building Flaw detection equipment Remotely powered electric motors Pipe bending machines Digital display device Television equipment Photovoltaic power Gear/thread machining machines Various precision measuring instruments Electrical power transmission	PDF	999 In-stock	Get Quote
815-UC3524DG4	Texas Instruments	UC3524DG4 Overview As a result of SOIC compact design, the switching controller is compatible with most applications. 2 outputs are supported by the dc motor controller. The switching controller is capable of switching at the 300kHz position. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. switching converters terminal (s) are designed to be at DUAL. There are many different types of terminations for 16. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 20V. 16 pins are present on switching converter. The type is a particular Switching Regulator or Controllers of switching converter. Statistically, the DC regulator outputs 5V voltage. The maximum duty cycle of this voltage regulator dc to dc is set to 45 % to ensure reliability during power-up and power-down. Switching controller operates at 450kHz Hz. A temperature 0°C lower than 0°C should be maintained. A temperature of 70°C more than 70°C degrees Celsius should be maintained in the undc regulator. In total, thare switch converters have 1 functions. A voltage regulators switching with 16 pins is designed. At maximum frequency, the controller can switch at 300kHz. It is possible to set the input voltage as 40V for nominal working statuses. Inputs of 100mA are ideal for this component. This algorithm outputs a value of 40V in normaloperation. Voltage is rated 40V for maximum supply. UC3524DG4 Features Switching Frequency: 300kHz PULSE WIDTH MODULATION Max Duty Cycle: 45 % Frequency: 450kHz UC3524DG4 Applications There are a lot of Texas Instruments UC3524DG4 DC to DC converter applications. Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots Industrial controllers Die casting equipment Injection molding machinery	PDF	80 In-stock	Get Quote
815-UC28023DWG4	Texas Instruments	UC28023DWG4 Overview The switching controller fits in the SOIC package and is ideal for most applications. dc motor controller is suitable for 1 output generation. With this switching controller, you can switch at 1MHz. Thare switch converters are connected to an analog integrated circuit (IC) of type SWITCHING CONTROLLER. There are a terminal (s) on the switching converters that are designed at DUAL. 16 terminations with various dc switching's functions. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. The DC switcher's nominal voltage is 15V. Total pins of switching converter are 16. Particularly, switching converter is a type of Switching Regulator or Controllers. The duty cycle of the voltage regulator dc to dc can be set to 100 % on power-up or power-down to ensure reliability. There is 1MHz frequency setting on the switching controller. In order to satisfy the need, DC to DC voltage regulator has a value of CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE. At -40°C and above, dc regulator should be kept. At a temperature around 105°C degrees Celsius, dc regulator should be running. Overall, the switch converters contains 1 function(s). Voltage regulators switching is designed with 16 pins. There is a maximum frequency of 1MHz that can be switched by the controller. It is possible to set the input voltage as 30V for nominal working statuses. A 200mA input is ideal for this application. This process outputs a value of 13V for normalworking processes. When it comes to maximum supply voltage, switching voltage regulators is rated 30V. UC28023DWG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 100 % Frequency: 1MHz CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE UC28023DWG4 Applications There are a lot of Texas Instruments UC28023DWG4 DC to DC converter applications. CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots Industrial controllers Die casting equipment Injection molding machinery Various CNC machine tools	PDF	10656 In-stock	Get Quote
815-UCC3813DTR-5G4	Texas Instruments	UCC3813DTR-5G4 Overview Capsuled in the SOIC package, the switching controller suits most application needs. PMIC is packaged in a solid enclosure of Tape and Reel. This switching controller can switch at 1MHz. The switch converters are connected to a SWITCHING CONTROLLER analog IC. The switching converters's terminals (s) are designed at DUAL. There are many different types of terminations for 8. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input of 10V. There are a total of 8 pins on switching converter. Switching converter is a special type of Switching Regulator or Controllers. This dc dc voltage regulator should be powered by a voltage of 4V. Statistically, the DC regulator outputs 4V voltage. Power-up and power-down reliability is ensured voltage regulator dc to dc by setting the maximum duty cycle to 50 %. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. Switching controllers work at 1MHz Hz. A temperature 0°C lower than 0°C should be maintained. DC regulator should run at a temperature 70°C higher than 70°C. 1 functions are available in total for the switch converters. It is designed to have voltage regulators switchings with 8 pins. There is a maximum frequency of 1MHz that can be switched by the controller. Ideally, it is suited for switching controllers with a 200mA input. normalworking processes output 1V voltage. Switching controller is necessary to provide a voltage of 10V. It is not recommended to supply more current to the controller than 30mA. Switching with 1 phases is the property of this controller. A maximum supply voltage of 12V is specified. UCC3813DTR-5G4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 50 % Frequency: 1MHz UCC3813DTR-5G4 Applications There are a lot of Texas Instruments UCC3813DTR-5G4 DC to DC converter applications. Terrestrial set-top boxes Die casting equipment Smart grid Fire elevators Printing Planers Solar power plants Flexible manufacturing cells Combined machine tools Cutting machine tools	PDF	999 In-stock	Get Quote
815-UCC2892DRG4	Texas Instruments	UCC2892DRG4 Overview In the SOIC package, the switching controller meets most application requirements. It is sufficient to generate 1 outputs with this dc motor controller. Packaging for the pmic consists of Tape & Reel (TR) solid enclosures. There is a switch at 1MHz that can be used with this controller. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. The switching converters's terminal (s) are designed at DUAL . The 16 terminations can be used for a wide range of dc switching. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's input voltageis 12V volts. 16 pins are present on switching converter. Switching converter is a special type of Switching Regulator or Controllers. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 73 %. A frequency of 1MHz is used by the switching controller. For safe and reliable operation in a circuit, voltage regulator dc to dc is suggested that users apply 12V. DC regulator should be kept at a temperature of -40°C or higher. Running the machine at 105°C is ideal. The switch converters have 1 function (s) in total. A voltage regulators switching with 16 pins is designed. It is possible for the controller to switch at a frequency of 1MHz. It is possible to set the input voltage as 110V for nominal working statuses. A 150mA input switching controller would benefit from it. This algorithm outputs a value of 11.1V in normaloperation. The supply voltage should be 12V. It is not recommended to supply more current to the controller than 3mA. A maximum supply voltage of 14.5V is specified. UCC2892DRG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 73 % Frequency: 1MHz UCC2892DRG4 Applications There are a lot of Texas Instruments UCC2892DRG4 DC to DC converter applications. Flexible manufacturing cells Series voltage regulation circuits Shearing machines Wind power Smoke exhaust equipment Surge protection circuits Sink circuits Hydro power Magnetohydrodynamic power Electrical distribution systems	PDF	999 In-stock	Get Quote
815-UC2823ADWG4	Texas Instruments	UC2823ADWG4 Overview As a result of SOIC compact design, the switching controller is compatible with most applications. 1 outputs are supported by the dc motor controller. The switching controller is capable of switching at the 1MHz position. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. switching converters terminal (s) are designed to be at DUAL. There are many different types of terminations for 16. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. It is inputted with a DC switcher's voltage of 12V. 16 pins are present on switching converter. The type is a particular Switching Regulator or Controllers of switching converter. Input voltage of dc dc voltage regulator must be 8.8V. Statistically, the DC regulator outputs 5.1V voltage. Voltages 20V are the maximum that the dc to dc regulator will accept. The maximum duty cycle of this voltage regulator dc to dc is set to 100 % to ensure reliability during power-up and power-down. Switching controller operates at 1MHz Hz. DC to DC voltage regulator has the value of CAN ALSO BE CONFIGURED IN CURRENT MODE to better satisfy the requirement. A temperature -40°C lower than -40°C should be maintained. A temperature of 85°C more than 85°C degrees Celsius should be maintained in the undc regulator. In total, thare switch converters have 1 functions. A voltage regulators switching with 16 pins is designed. At maximum frequency, the controller can switch at 1.1MHz. Inputs of 200mA are ideal for this component. This algorithm outputs a value of 2V in normaloperation. The supply voltage should be 12V. You should not supply more current than 36mA to the controller. Voltage is rated 22V for maximum supply. UC2823ADWG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 100 % Frequency: 1MHz CAN ALSO BE CONFIGURED IN CURRENT MODE UC2823ADWG4 Applications There are a lot of Texas Instruments UC2823ADWG4 DC to DC converter applications. Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots Industrial controllers Die casting equipment Injection molding machinery	PDF	12903 In-stock	Get Quote
815-TPS40052PWPR	Texas Instruments	TPS40052PWPR Overview For 1 outputs, the dc motor controller is appropriate. A SWITCHING CONTROLLER analog IC is connected to the switch converters. Switching converters are designed with the terminal (s) at position DUAL . There are many different types of terminations for 16. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. The nominal DC switcher's voltage input is 12V. There are 16 pins on switching converter. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. To run the voltage regulator dc to dc safely and reliably, users should apply 40V to the voltage regulator dc to dc. Keep dc regulator at a temperature of -40°C or above. DC regulator should run at a temperature of 85°C more than 85°C degrees Celsius. Overall, the switch converters contains 1 function(s). During dormancy, the dc switching uses 1.5mA. We are designing chips that have 16 pins. Maximum frequency of the controller is 1MHz. Input values of 20A make it ideal for switching controllers. As a result of normalworking processes, a voltage of 35V is output. TPS40052PWPR Features PULSE WIDTH MODULATION TPS40052PWPR Applications There are a lot of Texas Instruments TPS40052PWPR DC to DC converter applications. Industrial controllers Household control circuits Smoke prevention equipment Ball screw pair Automatic testing equipment Bending machines Milling machines Telecommunications equipment Die casting equipment Gear/thread machining machines	PDF	999 In-stock	Get Quote
815-UC28025DWRG4	Texas Instruments	UC28025DWRG4 Overview With its SOIC package, the switching controller fits the needs of most applications. For outputs of 2, this dc motor controller is suitable. Tape & Reel (TR) solid enclosure protects the pmic. In this switching controller, the switch can be set to 1MHz. SWITCHING CONTROLLER analog IC connects the switch converters. Switching converters are designed with the terminal (s) at position DUAL . The 16 terminations can be used for a wide range of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 15V is input. 16 pins are on switching converter. There is a particular type of Switching Regulator or Controllers in switching converter. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 100 %. Switching controllers work at 1MHz Hz. This value is CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE so that DC to DC voltage regulator better serves the purpose. Temperatures should be kept at -40°C or higher. There should be 105°C more than 105°C degrees Celsius in the machine. Total number of functions (s) for thare switch converters are 1. There is a design for voltage regulators switching with 16 pins. Maximum frequency of the controller is 1MHz. A nominal working status is achieved when the input voltage is set to 30V. Input values of 200mA make it ideal for switching controllers. normalworking processes output 13V voltage. Maximum supply voltage is 30V. UC28025DWRG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 100 % Frequency: 1MHz CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE UC28025DWRG4 Applications There are a lot of Texas Instruments UC28025DWRG4 DC to DC converter applications. Ball screw pair Computer application technology Network technology Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots	PDF	14842 In-stock	Get Quote
815-UCC3807DTR-3G4	Texas Instruments	UCC3807DTR-3G4 Overview Capsuled in the SOIC package, the switching controller suits most application needs. The dc motor controller is adquate to generate for 1 outputs. The pmic is packaged in Tape & Reel (TR) solid enclosure. This switching controller can switch at 1MHz. The switch converters are connected to a SWITCHING CONTROLLER analog IC. Terminal (s) of the switching converters are designed at the DUAL position. 8 terminations with a variety of function. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. 10V nominal DC switcher's voltage input. Switching converter has a total of 8 pins. Switching converter is a type of Switching Regulator or Controllers in particular. The minimum input voltage of the dc dc voltage regulator should be 4.3V. To ensure the reliability under power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set as 78 %. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sThe switching controller works at a frequency of 1MHz. DC regulator should be kept at a temperature of 0°C or higher. DC regulator should run at a temperature of 70°C more than 70°C degrees Celsius. The switch converters have 1 function (s) in total. The dc switching comes with 8 pins set. The controller can switch at the maximum frequency of 1MHz. It is ideal for switching controllers with 100mA input. Normally, it outputs a value of 400mV. UCC3807DTR-3G4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 78 % Frequency: 1MHz UCC3807DTR-3G4 Applications There are a lot of Texas Instruments UCC3807DTR-3G4 DC to DC converter applications. CNC system Servo drive system Digital display device Linear guide Ball screw pair Computer application technology Network technology Automation technology CMM Various precision measuring instruments	PDF	12262 In-stock	Get Quote
815-TL598CDG4	Texas Instruments	TL598CDG4 Overview Capsuled in the SOIC package, the switching controller suits most application needs. For 2 outputs, the dc motor controller is appropriate. The switching controller can be switched at 300kHz. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. Terminal (s) of the switching converters are designed at the DUAL position. 16 terminations with a variety of function. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 15V. The switching converter has a total of 16 pins. Switching converter is a type of Switching Regulator or Controllers in particular. 7V should be the minimum input voltage for the dc dc voltage regulator. A duty cycle set at 45 % ensures voltage regulator dc to dc reliability during power-on and power-off. Switching controller operates at 300kHz Hz. Keep dc regulator at a temperature of 0°C or above. DC regulator should run at a temperature 70°C higher than 70°C. The switch converters have 1 function (s) in total. A voltage regulators switching with 16 pins is designed. There is a maximum frequency of 300kHz that can be switched by the controller. It is ideal for switching controllers with 200mA input. It outputs a value of 12V in normaloperating procedures. Switching with 1 phases is the property of this controller. According to its maximum supply voltage rating, the voltage controller is rated 40V. TL598CDG4 Features Switching Frequency: 300kHz PULSE WIDTH MODULATION Max Duty Cycle: 45 % Frequency: 300kHz TL598CDG4 Applications There are a lot of Texas Instruments TL598CDG4 DC to DC converter applications. Milling machines Handheld GPS Computer monitoring equipment of building Automation technology Digital precision reference circuits Alternators Refrigerators of central air conditioners Pipe bending machines Low output voltage switching power supply circuits CMM	PDF	999 In-stock	Get Quote
815-TPS40195PWG4	Texas Instruments	TPS40195PWG4 Overview In the TSSOP package, the switching controller meets most application requirements. There is sufficient capacity to generate switching controller for outputs 1. It can switch at 600kHz. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. DUAL are the position of the terminal of the switching converters. Various 16 terminations. This dc dc converter ic uses a variety of control techniques, including PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 12V. There are 16 pins on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. DC regulator outputs 5.3V voltage based on test statistics. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 20V. You should keep dc regulator at -40°C degrees or higher. There should be 85°C temperature above 85°C degrees Celsius when dc regulator runs. 1 functions (s) are included in the switch converters. In dormant mode, 4mA is used. Designing voltage regulators switchings with 16 pins. Switching can take place at a maximum frequency of 580kHz. Since the dc switcher's maximum input voltage is 20V, the voltage must be regulated accordingly. This is an ideal solution for switching controllers with 20A inputs. During normaloperations, it outputs a value of 17V. Voltage 4.5V must be supplied. An output current greater than 20A cannot be provided by the dc switcher. Depending on the datasheet, the switching converter can output 17V volts at its peak. A voltage controller's lowest output voltage cannot be less than 591mV. TPS40195PWG4 Features Switching Frequency: 600kHz PULSE WIDTH MODULATION TPS40195PWG4 Applications There are a lot of Texas Instruments TPS40195PWG4 DC to DC converter applications. Network technology Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots Industrial controllers Die casting equipment	PDF	15983 In-stock	Get Quote
815-TL598CDRG4	Texas Instruments	TL598CDRG4 Overview With its SOIC package, the switching controller fits the needs of most applications. For outputs of 2, this dc motor controller is suitable. Tape & Reel (TR) solid enclosure protects the pmic. In this switching controller, the switch can be set to 300kHz. SWITCHING CONTROLLER analog IC connects the switch converters. Switching converters are designed with the terminal (s) at position DUAL . The 16 terminations can be used for a wide range of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 15V is input. 16 pins are on switching converter. There is a particular type of Switching Regulator or Controllers in switching converter. Input voltage of dc dc voltage regulator should be 7V. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 45 %. Switching controllers work at 300kHz Hz. Temperatures should be kept at 0°C or higher. There should be 70°C more than 70°C degrees Celsius in the machine. Total number of functions (s) for thare switch converters are 1. There is a design for voltage regulators switching with 16 pins. Maximum frequency of the controller is 300kHz. Input values of 200mA make it ideal for switching controllers. normalworking processes output 12V voltage. Phases of this controller are 1. Maximum supply voltage is 40V. TL598CDRG4 Features Switching Frequency: 300kHz PULSE WIDTH MODULATION Max Duty Cycle: 45 % Frequency: 300kHz TL598CDRG4 Applications There are a lot of Texas Instruments TL598CDRG4 DC to DC converter applications. Ball screw pair Computer application technology Network technology Automation technology CMM Various precision measuring instruments Various precision measuring detectors Flaw detection equipment Balance equipment Industrial robots	PDF	15732 In-stock	Get Quote
815-UC28023DWRG4	Texas Instruments	UC28023DWRG4 Overview With a SOIC package, the switching controller is suitable for a wide range of applications. For 1 outputs, the dc motor controller is appropriate. A solid enclosure of Tape and Reel surrounds pmic. Switching can be done at 1MHz with this switching controller. A SWITCHING CONTROLLER analog IC is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. An array of 16 terminations of dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 15V. There are a total of 16 pins on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. It is set to 100 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. A frequency of 1MHz is used by the switching controller. To better satisfy the need, DC to DC voltage regulator has a value of CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE. Ideally, dc regulator should be kept at a temperature of -40°C or higher. The temperature should not exceed 105°C degrees Celsius. In total, the switch converters have 1 function (s). We are designing chips that have 16 pins. There is a maximum frequency of 1MHz that the controller can switch at. Input voltage can be set to 30V for nominal working status. Switching controllers with 200mA inputs are ideal for it. As a result of normalworking processes, a voltage of 13V is output. In terms of maximum supply voltage, switching voltage regulators is rated 30V. UC28023DWRG4 Features Switching Frequency: 1MHz PULSE WIDTH MODULATION Max Duty Cycle: 100 % Frequency: 1MHz CAN ALSO BE CONFIGURED IN PEAK CURRENT OR AVERAGE CURRENT MODE UC28023DWRG4 Applications There are a lot of Texas Instruments UC28023DWRG4 DC to DC converter applications. Servo drive system Digital display device Linear guide Ball screw pair Computer application technology Network technology Automation technology CMM Various precision measuring instruments Various precision measuring detectors	PDF	4504 In-stock	Get Quote